Model airplane engine test stand-Build an Engine Test Stand

Fuel tank and smoke oil tank are installed and the throttle linkage and choke linkage are also worked out. But to adjust the carburetor and select the correct propeller, this is how I do it. Sullivan fuel tank. No over-heating at all. My wife was not pleased so I recommend an old table you can use exclusively for RC stuff.

Model airplane engine test stand

Model airplane engine test stand

Community Modfl. Believe you me The fuel tank mount is very simple and readily adjustable to maintain an appropriate Taylor tease torrent between the Model airplane engine test stand tank and the carburetor. But to adjust the carburetor and select the correct propeller, this is how I do it. In an effort to better serve you, our reader, and ensure a rich and relevant experience please help us by completing this Airplane interest profile. Related items to consider. You may also like.

Opera anal. Buy it now

No over-heating at all. Install two scrap 2-by-4 pieces at the opposite end of the base plate from the fuel tank and throttle control. The only engine stand designed with one wrench adjustments. Screw the Popsicle stick into the side of the base plate to act as the throttle control. Mounting this on the other end would make this stand suitable for just about any engine I am likely to run for quite a while. Additional boxes could be added for fuel bulbs, plug wrenches, etc. In an effort to better serve you, our reader, Model airplane engine test stand ensure a rich and relevant experience please help us by completing this Airplane interest profile. Sullivan fuel tank. Fuel tank and smoke oil tank are installed and the throttle linkage and choke linkage are also worked out. RC Engine Break in Stand. There is no real secret here, I Babe ma seb made a small bridge so I can use a strip of Velcro OneWrap from Vel-Tye, and shim the tank to an appropriate height using scraps of wood. All commercial rights reserved. Saito Engines or reinforced web engines Click here. Height Model airplane engine test stand, degrees rotating fuel tank mount.

I recently found the need for a engine test stand, and realized that the last one I had is either long gone or buried somewhere deep in my pile of RC shrapnel.

  • With a little ingenuity, you can test your model aircraft engines on a safe, homemade platform without shelling out extra cash to buy pre-packaged version.
  • I recently found the need for a engine test stand, and realized that the last one I had is either long gone or buried somewhere deep in my pile of RC shrapnel.
  • Fuel tank and smoke oil tank are installed and the throttle linkage and choke linkage are also worked out.
  • Click here.

I recently found the need for a engine test stand, and realized that the last one I had is either long gone or buried somewhere deep in my pile of RC shrapnel. A quick trip to the local home center for inspiration revealed a perfect starting point in the Black and Decker WorkMate, something many modelers likely already have. They had exactly one in stock, the floor display.

After negotiating a quick percent discount, I headed home with the base for my test stand, and, according to Black and Decker, a mighty handy tool for the home improvement workshop. With a little brainstorming I soon came up with the module shown.

It can be easily secured to the WorkMate yet is still relatively compact and easy to store. The crux of this design is the modular firewall. I hit upon the idea of using face plates that could be removed and replaced as they get used up. This also makes mounting a new engine easy as I can set it up using the drill press and workbench and then attach the assembly to the test stand as a single unit.

I also made a box to hold a battery and servo driver for glow engines or an ignition battery for gas engines. Additional boxes could be added for fuel bulbs, plug wrenches, etc. The fuel tank mount is very simple and readily adjustable to maintain an appropriate relationship between the fuel tank and the carburetor. There is no real secret here, I just made a small bridge so I can use a strip of Velcro OneWrap from Vel-Tye, and shim the tank to an appropriate height using scraps of wood.

One thing I have noticed over the years is that using a conventional clip-on glow driver may not be the best setup for working on a test stand. The Mcd has an internal battery and is traditionally set up to run from a receiver. Instead I am using a 4-cell flight pack battery and an Astro Flight servo driver.

The Mcd has a bright red LED that is readily visible in sunlight so I know when the plug is hot or not. Like any project, there are some design features that seemed like a good idea at the time that I would change. The main thing would be to not extend the firewall below the main base plate.

I could then reverse the test stand on the WorkMate. I have one of their smaller mounts, designed for glow engines up to. Mounting this on the other end would make this stand suitable for just about any engine I am likely to run for quite a while. I am very happy with how this stand turned out, and encourage you to consider something similar for your own needs.

If you want to build a similar test stand of your own, you can download a revised drawing by clicking the link below. Engines , distributed exclusively by Great Planes.

Saito Engines , distributed exclusively by Horizon Hobby. Click here to download the free PDF plans. Feel free to adapt as needed for your personal use. All commercial rights reserved. Please email any questions or comments to thayers flyrc.

Engines , distributed exclusively by Great Planes www.

Do you have a video to share with Model Airplane News? Subscribe Button Subscribe. No over-heating at all. How to break in an RC engine. Drill small holes into the top of these to serve as screw holes for mounting the engines. Download Page.

Model airplane engine test stand

Model airplane engine test stand

Model airplane engine test stand

Model airplane engine test stand

Model airplane engine test stand

Model airplane engine test stand.

.

MK 2 Special Model Engine Test Stand RC for sale online | eBay

Fuel tank and smoke oil tank are installed and the throttle linkage and choke linkage are also worked out. But to adjust the carburetor and select the correct propeller, this is how I do it. Sullivan fuel tank. No over-heating at all. My wife was not pleased so I recommend an old table you can use exclusively for RC stuff.

The box is also very easy to remove after testing and I keep it handy in the workshop. It comes in convenient 2. Starting procedure is: 1, close the choke and open the throttle fully.

I used a digital GloBee optical tachometer to check the numbers. I really like using this engine test box setup to adjust my engines, especially large gasoline buring beasts.

Give it a try. Your email address will not be published. Do you have a video to share with Model Airplane News?

Submit your video here. Profile Data. In an effort to better serve you, our reader, and ensure a rich and relevant experience please help us by completing this Airplane interest profile.

I would like to subscribe to the Model Airplane News Newsletter. Hangar Login. Not a member? Join today! Subscribe Button Subscribe. Gerry Yarrish. Zenoah Engines Engine shown in the unfinished Triplane. Notice clearances cut for proper cooling. Test flight day at the flying field.

The GT fired right up without a hitch! Leave a Reply Cancel reply Your email address will not be published. Featured Video. Sitewide Ads. Man Subscribe Sidebar.

Profile Form Profile Data. Show ad. WordPress Lightbox.

Model airplane engine test stand

Model airplane engine test stand